Semi-Active Suspension Control Considering Lateral Vehicle Dynamics Due to Road Input

© 2012 Suzuki and Takahashi, licensee InTech. This is an open access chapter distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Semi-Active Suspension Control Considering Lateral Vehicle Dynamics Due to Road Input


Introduction
An automotive performance has improved from the demand of ride comfort and driving stability.Many research have proposed various control system design methods for active and semi-active suspension systems.To improve vehicle response by steering, a roll angle control [1], a distribution control of the suspension stiffness of front and rear [2], and pitch angle control [3] [4] have been proposed.Furthermore, to improve vehicle response due to disturbance on the road, a tire vertical load control [4][5][6] caused by road disturbance was proposed.In recent year, it is reported that roll and lateral vehicle motions are affected by the road input.These motions are affected by not only road displacement but also the change of tire side force [8][9][10][11].As shown in Figs. 1 and 2, the tire side force is caused by a toe change and a scuff due to the roll motion and tire side force.However, there are few research about a suspension control method which takes into consideration with a suspension characteristic that is change of tire side force caused by suspension stroke and tire side force.
In this research, we designed a suspension control system which reflects a suspension characteristic, the change of tire side force caused by suspension stroke and tire side force.A new semi-active suspension control method is proposed to reduce the vehicle vibration and vehicle lateral motion due to the road input.
To design such a system, the time delay of the road input from the front wheel to the rear wheel needed to be modeled.In the vehicle control, there are several control systems which take into consideration with this delay [12][13][14][15][16].However, the purpose of these research is to find a way to reduce the vehicle vertical vibration.Oraby evaluated motion of the vehicle lateral direction [7].However, the dynamics of the lateral direction do not be considered in the control system design.

Table 1. Specification of vehicle model
In order to design the controller, a vehicle model including the tire side force change caused by road disturbance is constructed.Moreover, the road input from the front wheel to the rear wheel time delay is modelled with Pade approximation.These suspension characteristics and the time delay are modelled with liner model.The disturbance accommodating H∞ control which considers the vehicle model including the suspension characteristic is proposed.In the control, we set the lateral acceleration of the vehicle to one of controlled outputs.New semi-active suspension control method is proposed to reduce the vehicle vibration and vehicle lateral motion due to the road input.To verify the feasibility of the proposed method, several numerical simulations are carried out.

Modeling of the vehicle
Figure 2 shows a full vehicle model which is equipped with semi-active suspension between each wheel and the vehicle body.The weight of the vehicle body is supported by the spring.We assume that a vehicle model is a generic sedan car as shown in M b , I r , I p ,I y

Side view
Rear view

Plane view
Forward The spring coefficients of each wheel are different from each other, and were set to K1, 2 = Kf , K3, 4 = Kr, Fyi means a tire side force, zsi means a suspension stroke of each wheel, zti means deformation of the each tire.
As shown in Fig. 2, tire side force is caused by the toe change and the scuff.The toe change and the scuff are caused by the suspension stroke and the tire side force.The tire side force of each tire, Fyi , is as follows: where, a value in the parenthesis in Eq.( 3) means the tire slip angle of each tire.Ksf and Ksr are the coefficient of toe angle change caused by suspension stroke.The third term in the parenthesis is the toe angle change caused by the suspension stroke of each wheel, as shown in Table 2 (A).The fourth term in the parenthesis is the tire slip angle caused by the scuff per unit time as shown in Table 2 (B).The equivalent cornering stiffness which includes the compliance steer is as follows: where, KCi is the cornering stiffness of each tire.KSFi is the coefficient of the toe angle change caused by the tire side force, as shown is Table 2 (C).Finally, the characteristic shown in Table 2 (D) is derived from a first order delay of the equivalent cornering stiffness (Eq.( 4)).
( 1,...4) where, KPFi is the coefficient of the scuff caused by the tire side force.The characteristics of the tire side change is modelled from Equations ( 3) to (5).As shown in Table 3, each parameter is determined that stability factor was set to the usual value, 1.43×10 -3 s 2 /m 2 based on the reference [18].

Vehicle response caused by antiphase road disturbance
The state equation of the vehicle model which reflects change the tire side force is defined as Eq. ( 6).This model is an LTI model when the vehicle velocity is fixed.
We confirmed that the vehicle responsed to an antiphase road disturbance.In this research, the phases of road input of left-right are zero and π.Zero means a coordinate phase, and π means the antiphase.In the antiphase road, the road displacement at the vehicle velocity, V, is as follows., , The transfer function of the vehicle responce caused by the antiphase road disuturbance at 33.3 m/s (120 km/h) is shwon in Fig. 3. Here, Figure 3 (a) is the date of previous study.Figure 3 (b) is the data of our study.In these figures, specification of the vehicle model of each study is different.However, from the result showing the same tendency for vehicle responses, we found that the our model is appropriate.

Design of damper coefficient
In general, the performance of the controller is affected by the damping coefficients of the suspension.In this section, we design the damping coefficient for the evaluation values which are the vertical acceleration at the coordinate phase road and the lateral acceleration at the antiphase road.In the next section, we design the control system which uses the damping coefficients designed in this section.The road condition is shown in Figs. 4 and 5.
The road displacement is assumed such that the Power Spectral Density (PSD) characteristic of the road surface is C class defined by ISO [19].The lateral accelerations are shown in Fig. 8 and the lateral acceleration of vehicle body are derived from a geometric relation as follows.The sensitivity curves of the lateral and the vertical acceleration are defined by ISO [20].We designed the damping coefficient for the suspension to minimize the Root Mean Square (RMS) which considers the sensitivity curves.A frequency response of the filter [21] which modeled sensitivity curve with the transfer function is shown in Fig. 7.We calculated the RMS values using the time history of the vertical and lateral accelerations which pass this filter.The simulation results when both front and rear damping coefficients are changed are shown in Fig. 8, which is a contour diagram of the RMS values.There are minimum point in Fig. 8

Controller design
We used the controller designed based on the linear H∞ control theory to a semi-active suspension.The control system of the semi-active suspension is shown in Fig. 9.An actuator force command Fli is calculated with the linear H∞ controller.The damping force command Fdi is translated with a liner-bilinear converter.

Approximation of time delay of road disturbances
When the front and rear tire passes the same path, road disturbance affects the rear tire has the delay to the front tire.As shown in Fig. 10, the road input from the front wheel to the rear wheel is the delayed.The delay is modeled with a third-ordered Pade approximation.As shown in Fig. 10 (b), we consider the effect of vehicle velocity in the control system design by using a linear model.To check whether the Pade approximation is correct, we carried out the numerical simulations.The response of the vehicle model which includes the Pade approximation when the vehicle runs on the antiphase road disturbance is shown in Fig. 11.The vehicle velocity is 16.7 m/s (60km/h).In the lower frequency of the resonance frequency of the tire, we found that the result of the simulation model which uses the time delay and Pade approximation are almost the same.

Disturbance-accommodating control
We found that feedforward control of disturbance information in the finite frequency range and feedback control improve performance [22].The power spectral density of the actual velocity of disturbances had flat characteristics in a low frequency, and decreased according to frequency at a region of high frequency.We assumed that it regarded as the colored noise formed by shaping filter which has a transfer function with low-pass characteristics.This filter of the each wheel is based on the road condition which defined by ISO [19] .The filter is as follows: where, wgi is road input of the each wheel, wi is road input of the vehicle model of the general model as shown in Fig.

Disturbance-accommodating H∞ control
The feedforward control of disturbances resulted in worse accuracy outside the assumed frequency [22].Furthermore, because each resonance frequency of the vehicles and tire differs, the control system design considering each resonance frequency is needed.Therefore, the control system was designed by using the H∞ method in the control theory.
We integrated each state variable of the road disturbance model and frequency weights for controlled values.The frequency weights are as follows: where, zzc is controlled value of the vehicle motion, zzi is controlled value of the control input.Figure 7 shows a block diagram of the generalized plant to design the controller, and the state-space form of the generalized plant is as follows: Pade approximation (Simulation model)

Real world
Pade approximation (Simulation model) H∞ norm of the transfer function from disturbance wg(t) to controlled value z(t) is expressed by the following equation.
sup : where,  * is a minimum of H∞ norm of the generalized plant realized with H∞ controller.
The controller is the following equation [23].
In this reserch, we assumed that the vehicle speed is constant.The measured outputs, y(t), are four vertical accelerations of the wheel position of the vehicle body.The controlled values, z(t), are vertical acceleration, lateral acceleration, vertical velocity of the vhicle body, tire deformation, and actuating force.Frequency weight Wi, shown in Fig. 13, was determined by trial and error.
A bandpass filter, W1, that had a peak frequency equal to the resonance frequency of the passenger's head was used based on sensitivity curves [20], such as that being standardized by ISO and shown in Fig. 4. The low pass filter, W2, was used based on sensitivity curves of lateral direction.In order to prevent the increase of response in each resonance, a low pass filter W3 and a bandpass filter W4 are used.Moreover, to prevent steady control input, a high pass filter, W5, was used.

Comparison of the response of the frequency weight Kw2
To check the effect of the suspension model which includes the tire side force caused by the road disturbance, we compared two control systems, one which considers the tire side force and the control system, and one which does not consider one.The design of two general control methods changed the controlled value of the lateral acceleration of the vehicle body.Frequency weights, W1, W2, W3, W4, Kw1 = 500, Kw3 = 500, Kw4 = 2000, and Kw5 = 20, are the same value in the proposed method and general methods.We combined the control system and vehicle model which includes the tire side force shown in Chapter 2. We used MATLAB (The Math Work Inc.) to calculate the Runge-Kutta method for the differential equations.The computational time step is 1 ms.Vehicle velocity is 16.7 m/s (60 km/h).The road surface conditions are shown in Fig. 5(b).We calculated the RMS values from the time history of lateral acceleration which passes the filter shown in Fig. 7.The RMS value changed by the frequency weight, Kw2 is shown in Fig. 14.For a frequency weight, Kw2, is 1 to 4000, when Kw2 increases, the RMS value of rolling and lateral accelerations decreased.Furthermore, when Kw2 increases, RMS of lateral acceleration decreased.From the result of Fig. 14.(b), it was confirmed that the proposed method can reduce the lateral acceleration due to the road disturbance in comparison with the general method.We compare the control performance of two controllers which are designed using the frequency weight shown in Fig. 14.(b).In two controllers, Kw2 is set the smallest RMS value in 14.(b).

Simulation condition
To clarify the effect of the suspension model which includes the tire side force, we compare the two control systems.The two control systems are designed in Cheater 3. As for the control system which inflects the tire side force (H∞ cont.(with susp.model)), the frequency weight of lateral acceleration, Kw2, is 4000.The control system which does not consider the tire side force (H∞ cont.(without susp.model)), the frequency weight of lateral acceleration, Kw2, is 6000.
In the simulation, we combine the control system and the vehicle model which includes the tire side force shown in Chapter 2. The vehicle velocity is 16.7 m/s (60km/h).Moreover, we assume that the range of the damping coefficient of the semi-active suspension is 100-10000 N/m/s in Fig. 15.The semi-active damper has the first order delay.The cut off frequency is 10 Hz.We used MATLAB (The Math Work Inc.) to calculate the Runge-Kutta method for the differential equations.There were two road conditions.One is the coordinate phase road in Fig. 5 (a), and the other is the antiphase road in Fig. 5 (b).To demonstrate the control effect, we show the responses which does not control he semi-active damper (Non control).

Simulation results
In check whether the proposed method reduced vertical and lateral motion, we did the numerical simulations.The time history of the vertical acceleration caused by the coordinate phase and the lateral acceleration caused by the antiphase road is shown in Fig. 14.The Lissajous figure for the suspension velocity and the damping force of the front suspension are shown in Fig. 15.The PSD of the vertical acceleration and the lateral acceleration is shown in Fig. 16.
In the coordinate phase road, there are few difference in the time history and the Lissajous figure.As for the PSD, two control systems can reduce the vibration better than the non control one near the resonance frequencies of the vertical direction of the vehicle body and vertical direction of the human head.On the other hand, in the antiphase road, there are differences in the time history and the Lissajous figure.The PSD of lateral acceleration, two control systems can reduce the vibration near the frequency range with a high level of lateral acceleration sensitivity.Additionally, the control system which includes suspension model of the tire side force change caused by road disturbance can reduce the vibration better than the control system which does not include the tire side force change in the same frequency range.The simulation results confirmed that using the proposed control system reduces the vertical and the lateral motion of the vehicle caused by the disturbance in the road.

Conclusion
This research proposed disturbance accommodating H∞ control which considers the vehicle model in order to reduce the vehicle vibration and vehicle lateral motion due to the road input.We formulate the vehicle model including the suspension characteristic that is the toe change and the scuff caused by suspension stroke and tire side force.In order to verify the feasibility of the proposed method, the numerical simulations were carried out.From the result, it was confirmed that the proposed control system is effective for reducing not only the vertical vibration but also the lateral vehicle motion due to the road disturbance in comparison with the control method without considering the suspension characteristic.

Figure 1 .
Figure 1.Toe change and scuff caused by roll motion and tire side force.

Figure 2 .
Figure 2. Vehicle model where Hr is the distance from a roll center to the CoG of the vehicle body, and Hp is the distance from a pitch center to the CoG of the vehicle body.These parameters are constant.

Figure 4 .Figure 5 .Figure 6 .Figure 7 .Figure 8 .
Figure 4.Power spectral density of road surface profile[19] (a), (b) and (c).The evaluation value is the sum of vertical and lateral acceleration of RMS shown in Fig. 8. (c).From the simulation results, the damping coefficients of the suspension are 2000 and 1300 N/m/s.

Figure 14 .
Figure 14.RMS value changed by evaluation function of accelerations (Antiphase road) a) Rolling acceleration (b)Lateral acceleration

Table
. The equations of motion which are, lateral, bounce, roll, pitch, yaw, and each unsprung motion are as follows:

Table 2 .
Modeling of suspension characteristics

Table 3 .
Specification of suspension characteristics